Carpets and floor mats take more abuse than any other part of a car's interior. Every time you get in, you bring sand, mud, crumbs, hair and whatever was on the parking lot along with you. Over time that grit works deep into the fibers, mats start to look flat and gray, and a stale smell creeps in. The good news is that a careful vacuum, a good brush and the right cleaner bring most carpets back to life.
Here's how we detail carpets and floor mats at Vital Detail Supplies.
What you'll need
- A good vacuum with a crevice tool. A shop vac works, or a cordless option like the Fanttik Slim V8 Apex Car Vacuum. The Buff Brite Sidewinder crevice tool reaches deep under and between the seats.
- Carpet brushes. The Vikan Carpet Brush is a staple for scrubbing and patterning carpets, and works wet or dry. For larger areas, Drill Brush Attachments or the Work Stuff Drill Brush save a lot of elbow grease.
- A carpet striping tool like our Carpet Stripe/Pet Hair Remover Tool for the finishing lines.
- A carpet and upholstery cleaner (see Step 4).
- A rubber mat cleaner and protectant if you have all-weather mats.
- Clean microfiber towels and a spray bottle.
- Optional: a compressed-air tool like the Tornador Air Blow Out Tool and a carpet extractor.
Step 1: Pull the mats and clear the car
- Remove all floor mats and set them aside. You'll clean them separately.
- Take out trash, loose items and anything under the seats.
- Slide the front seats all the way forward to reach the rear footwells, then all the way back to reach under the front.
Step 2: Loosen, then vacuum
Most of the dirt in a carpet isn't sitting on top. It's packed down at the base of the fibers, so vacuuming alone leaves a lot behind.
- Agitate first. Brush the carpet briskly with the Vikan Carpet Brush in several directions to break up packed dirt and stand the fibers up.
- Blow out the edges. If you have compressed air, blow sand out of seat rails, seams and the edges where the carpet meets the trim, aiming the debris toward the center of the floor.
- Vacuum slowly in overlapping passes, going in two directions. Slow passes pick up far more than fast ones.
- Get the edges with a crevice tool along the seat rails, center console and door sills.
For stubborn hair and lint, a vacuum aid like P&S Release Vacuum Aid is made to help loosen embedded pet hair and trapped dirt so the vacuum can pull it out.
Pro tip: brush, vacuum, then brush and vacuum one more time. The second round almost always pulls out more sand than you'd expect.
Step 3: Pre-treat spots and stains
Before you shampoo the whole carpet, hit the obvious spots: coffee, soda, grease, food and salt lines.
- P&S Terminator Enzyme is made to pre-treat spots and stains on carpet and upholstery before shampooing, and cuts grease, oil and food stains.
- Stinger 709 Enzyme Carpet & Prespotter uses live cultures and is a great choice for organic stains and pet accidents.
Always test a cleaner in a hidden spot first, follow the label, and don't let it dry on the carpet.
Step 4: Shampoo the carpet
For light to moderate dirt, you can clean carpets by hand with a spray cleaner, a brush and towels. Popular options we carry include Shine Supply Carpet Cleaner, Rebels of Shine Carpet Blaster, P&S Carpet Bomber and Labocosmetica GLICO. Dilute according to the label.
- Work one section at a time, about the size of one footwell.
- Mist the cleaner lightly. You want the fibers damp, not soaked. Over-wetting pushes dirt down into the padding and makes the carpet slow to dry.
- Scrub with the Vikan brush or a drill brush on low speed, working in a few directions.
- Blot and lift the dirty foam with a clean, folded microfiber towel, flipping to a clean side often.
- Repeat on heavily soiled areas rather than scrubbing harder.
Step 5: Extract for a deep clean
A carpet extractor sprays clean solution into the fibers and immediately vacuums the dirty water back out. It's the best way to deep clean heavily soiled carpets and seats, and it leaves them much drier than hand shampooing.
- Machines: the Mytee 8070 Heated Carpet Extractor and the compact Mytee S-300H are pro favorites. For a cordless spot cleaner, check out the Fanttik Textra 11 Apex.
- Extractor solutions: use a low-foaming product made for extractors, like Nanoskin Extractor Shampoo, Kleentech Xtract Solution or Ultra Clean Extractor HD. High-foaming shampoos can overflow the recovery tank.
Make one or two wet passes, then several dry (vacuum-only) passes to pull out as much water as possible. Check your machine's manual for setup and cleaning solution guidance.
Step 6: Clean the floor mats
Carpet mats
Treat these exactly like the carpet: shake or beat them out, brush, vacuum, spot treat, then shampoo or extract. Because they're out of the car, you can scrub them more aggressively and even rinse them with a hose, as long as you extract or squeeze out as much water as possible and let them dry fully before they go back in.
Rubber and all-weather mats
- Rinse off loose dirt.
- Spray with a dedicated mat cleaner like McKee's Floor & Mat Cargo Rejuvenator or a diluted all-purpose cleaner, and scrub the grooves with a stiff brush.
- Rinse thoroughly and dry with a towel.
- Finish with Adam's Rubber Mat & Liner Protectant, which dries to a non-slippery satin finish.
Safety note: never use tire shine or slick dressings on floor mats or pedals. A slippery mat under the driver's feet is dangerous.
Step 7: Finish with carpet lines
Striping the carpet is the detail that makes people say "wow" when they open the door. Once the carpet is clean and vacuumed (and dry, or just slightly damp), pull a Carpet Stripe Tool or the Vikan Carpet Brush across the carpet in straight, even passes, all in the same direction. Overlap each pass slightly. For a classic look, run the lines front to back; for a checkered pattern, make a second set of passes across them.
Start at the far side of the footwell and work toward the door so you don't step on your finished lines.
Step 8: Dry it completely
Damp carpet and padding are a recipe for mildew smells. After shampooing or extracting:
- Leave the doors or windows open in a warm, dry, ventilated spot.
- Run the car's heater and fan, or set a fan blowing into the footwells.
- Press a dry towel into the carpet to check for moisture before putting the mats back.
Once dry, a fabric protector like Gtechniq I1 Smart Fabric helps the carpet resist water-based stains so the next cleaning is easier.
Carpet and mat checklist
- Remove mats and clear the car
- Brush, blow out and vacuum, then do it again
- Pre-treat spots and stains
- Shampoo lightly by hand, or extract for a deep clean
- Clean carpet mats like carpet; scrub and protect rubber mats
- Stripe the carpet
- Dry everything completely before reinstalling mats
Want streak-free windows to go with your clean carpets? See our guide on streak-free glass, inside and out.
Not sure which carpet cleaner or extractor fits your needs? Stop by our store at 9121 Garvey Ave in Rosemead or call us at (626) 656-6226, and we'll help you put together the right setup. Happy detailing!

